Starke Venom Water Spot and Stain Remover

Venom is a new generation water spot remover that is safe to use on finishes that have been ceramic coated. In addition, it is also safe to use glass, paint, gel coat, and metal. The formula has a consistency that allows it to gel to the substrate where it then starts to lightly eat away at minerals and other contaminants.

Why Charleston boaters keep Venom on the shelf

Salt air, humid nights and rinse water drying on the boat leave mineral deposits that soap will not touch, and they build up on top of ceramic coatings until the water stops beading. Venom’s acidic gel formula (pH ~3.4) clings to vertical hull sides, the waterline and outrigger hardware long enough to work. That makes it three tools in one bottle:

• Strip wash for ceramic-coated boats: lifts the contamination layer off the coating, then follow with Starke Replenish
• Water spots on gelcoat, glass and stainless steel
• Rust staining from anchor chain contact, dock hardware or iron-bearing water

Venom can also be used as a pre wipe before buffing or light polishing. This benefit allows you to save a massive amount of time because you are able to begin polishing a very clean substrate which make your job easier.

We are confident when we say there is nothing else out there on the market like this. Developed by professional detailers, this is a must have product in your arsenal!

How to Use Venom Water Spot Remover

Materials Needed:

• Venom Water Spot Remover
• Microfiber towels (clean and dry)
• Soft applicator pad or microfiber applicator (optional)
• Buffing or polishing machine (optional, for advanced application)
• Chemical-resistant gloves and eye protection

Step 1: Surface Preparation

1. Ensure the surface is cool and dry before starting the application. It's best to work in a shaded area to prevent the formula from drying too quickly.
2. Pre-rinse the area lightly to remove any loose debris or dirt to avoid scratching during the cleaning process.

Step 2: Application of Venom

1. Shake the bottle of Venom well before use to ensure an even consistency.
2. Apply a generous amount of Venom directly onto the affected areas with water spots or mineral buildup (gel coat, paint, glass, or metal).
   • For more control, you can apply the formula with a soft applicator pad or microfiber applicator.
   • The gel-like consistency will stay in place on vertical surfaces and allow the formula to work effectively.

Step 3: Let It Sit

1. Allow the formula to sit for 2-5 minutes on the affected area. Venom will begin to break down water spots, mineral deposits, and contaminants.
   • Keep an eye on the surface during this time to prevent the product from drying out.

Step 4: Wipe Off

1. After the allotted time, use a clean microfiber towel to gently wipe away the Venom.
2. If necessary, use a second clean microfiber towel to remove any excess residue and reveal a clean, smooth surface.

Step 5: Polishing or Buffing (Optional)

1. If you are planning to buff or polish the surface, Venom can be used as a pre-wipe before starting.
   • By cleaning the surface with Venom, you remove any contaminants, allowing you to begin polishing on a clean substrate, which saves time and ensures a better finish.
2. For polishing, continue with your preferred compound or polish after using Venom for optimal results.

Step 6: Final Wipe

1. After the water spots are removed and any polishing is completed, wipe the surface one last time with a clean microfiber towel to ensure the finish is clear and spotless.

Additional Tips:

• Use Venom on ceramic-coated surfaces without worry—it’s safe and will not harm the coating.
• Always test on a small area first to ensure compatibility with your surface, though it’s generally safe for all gel coats, paints, metals, and glass.
• Use Venom regularly to keep your boat looking spotless and prevent the buildup of water spots or contaminants.

Safety notes

• Wear chemical-resistant gloves and eye protection, and rinse thoroughly.
• Test aluminum, anodized surfaces and tinted glass first.
• Keep Venom away from MFD screens, chart plotters and electronics displays. It will permanently strip their UV-protective coating.

Available in 16 oz. and 128 oz. Pick it up at Marine Detail Supply Charleston, 7644 Southrail Rd, Unit 400C, North Charleston, SC, Monday–Friday, 8 a.m.–4 p.m. (closed weekends), or call 843-256-3383.

Safety Data Sheet

Shipping

• Free shipping on orders over $200 in the domestic United States
• $7 flat rate on orders under $200
• Orders ship via UPS Ground or USPS Priority Mail
• Questions? Call 843-256-3383